Final goal TÜV@HD. Why? Because they know those types of motorcycles… In the end no reason for an objection or reclamation. This was the planned “winter thread”, ended in 05/2017 and (finally) documented 09/2017 but since the name is changed to the “Project2017” there is still more to do… keep you posted! -LeMarque
Screw Change (V2A)
In the end the rest of the team – VA2 stainless steel screws. Just some pictures. Special thanks to Bernd from buell-parts.com ! Handelbar clamp Loctite 243 (BLUE) + 13,6-16,3NM , fuel tank only hand tighten. Break and clutch lever clamp 9-10,2NM, housings 3-4NM Oil reservoir hand tighten. Frame Loctite 243 (BLUE) + 28,5-31,2NM, foot…
Oil Change
Mandatory in the end – oil change! These are the tools: 5/8 HEX TX 27 torque wrench Loctite 565 Loctite 271 oil pan aluminum foil oil filter claw measuring cup and funnel These are the service parts: 1x OEM oil Filter 2x O-ring 1x omega gasket 1x service gasket 3 Liter full synthetic 15W50 (Fuchs Pro…
Bodywork Installation
Just one step ahead from touchdown – this time I’ll assemble the air scoops, pulley cover, front fender and chin fairing. Related posts: Stainless Steel Screws Air Scoops These are the tools: 5/32 HEX 3/16HEX TX 27 torque wrench Loctite 243 Loctite 271 Terms and conditions: All work at own risk, NO warranty in ANY case of…
Fork Service (2/2)
Now it’s time to get off the xb12 from the paddock stand – fork and front wheel installation! Related posts: Fork Service (1/2) Front Brakepads These are the tools: 1/4 HEX 5/16 HEX 22 HEX (metric) 22 NUT (metric) plastic wedge torque wrench anti seize Loctite 271 Terms and conditions: All work at own risk, NO warranty in ANY…
Rear Wheel Installation
Finally the rear wheel back in place. Related posts: Rear Wheel Removal Rear Pulley Installation Idler Pulley Installation These are the tools: 5/16 HEX 3/8 HEX 22 HEX (metric) 22 NUT (metric) torque wrench anti seize Loctite 243 Terms and conditions: All work at own risk, NO warranty in ANY case of damage! STEP 1 First…
Rear Pulley Installation
Now it’s time to install the new pulley. Related posts: Rear Wheel Removal These are the tools: 7/32 HEX torque wrench anti seize Loctite 243 Terms and conditions: All work at own risk, NO warranty in ANY case of damage! STEP 1 First is to prepare the wheel on the table. Make sure the breaking rotor…
Swingarm Brace Screws (LEGO)
Just an interim stage in the assembly. As posted in Stainless Steel Screws I change a lot of OEM screws to stainless ones. The screws of the lego swingarm should only be removed when the rear axle is NOT tighten! Related posts: Rear Wheel Removal These are the tools: 1/4 HEX torque wrench anti seize Terms and conditions: All work at…
Idler Pulley Installation
Next step in reassembly is the idler pulley. Related posts: Idler Pulley Bolt Sprocket Installation These are the tools: 9/16 NUT torque wrench Terms and conditions: All work at own risk, NO warranty in ANY case of damage! STEP 1 Put the belt around the sprocket and install the idler pulley on the bolts. The belt runs…
Sprocket Installation
Finally it’s time for reassembly – first of all the Sprocket! Related posts: Rear Wheel Removal Sprocket Removal These are the Tools: 1/4 HEX 1 7/8 NUT sprocket locking tool torque wrench fixed wrench angle protractor Loctite 243 Loctite 271 Terms and conditions: All work at own risk, NO warranty in ANY case of damage! Step…
Sprocket Locking Tool
A short introduction to another xborg built – sprocket locking tool. Originally you need the HD “sprocket holding tool” (B-43982) and “sprocket locking tool” (B-45659) to remove and install the front sprocket. Very expensive… Therefore the xborg community crafted another fine workaround-tool which is easy to recreate… but I bought one from a member =D…
Idler Pulley Bolt
After a test fit of the idler pulley I realised a length difference on the bolts. Therefore I reinstalled both of them. Related posts: Rear Wheel Removal These are the Tools: 9/16 NUT 9/16 WRENCH Loctite 271 RED Terms and conditions: All work at own risk, NO warranty in ANY case of damage! Step 1 After removing the…